NCP1578
http://onsemi.com
14
SMPS is disabled by EN_SW. Note that the PGOOD pin is
valid providing LDO5 is high enough to maintain the
internal logic state.
Overvoltage Protection
When SMPS output voltage is above 115% (typ) the
preset nominal regulation voltage for 16 consecutive
internal clock cycles, the SMPS output will be latch off and
it can be restarted by toggling EN_SW or LDO5.
Undervoltage Protection
When SMPS output falls below 65% (typ) of the nominal
regulation voltage for 16 consecutive internal clock cycles,
the undervoltage fault is set, the SMPS is latched off.
Cycling EN_SW or LDO5 can reset the undervoltage fault
latch and restart the controller.
Soft-Start
The switcher V
OUT
soft-start feature is incorporated in
the device to prevent surge current from power supply and
output voltage overshot during power up. When EN_SW,
LDO5 rises above their respective upper threshold voltages,
the external soft start capacitor C
ss
is charged by a constant
current source I
ss
. When the soft-start voltage reaches the
V
ref
voltage, the soft start process is finished. The soft-start
time Tss can be programmed by the soft-start capacitor
according to the following equation: T
ss
[ (0.8 x C
ss
) / I
ss
.
OPERATION TABLE 1 (Single Supply V
BAT
Configuration)
Input Condition
Operating Condition
Output Condition
FPWM
EN_LDO
EN_SW
SMPS
LDO5
PGOOD
X
Low
X
Off
Off
H-Z
X
High
Low
Off
On
Low
High
High
High
On (FPWM)
On
H-Z
Low
High
High
On (DCM or Pulse Skipping)
On
H-Z
OPERATION TABLE 2 (External +5 V and V
IN
Configuration (Note 4))
Input Condition
Operating Condition
Output Condition
FPWM
EN_LDO
(Note 5)
EN_SW
SMPS
PGOOD
X
Low
Low
Off
Low
High
Low
High
On (FPWM)
H-Z
Low
Low
High
On (DCM or pulse skipping)
H-Z
4. External +5 V is connecting to V
BAT
and LDO5 pin.
5. For this configuration, it is recommended to pull EN_LDO to GND at any time.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NCP1601BDR2G
IC PFC CTRL CRM/TRANSITION 8SOIC
NCP1603D100R2G
IC CTLR PFC/PWM COMBO 16-SOIC
NCP1605DR2G
IC PFC CONTROLLER CCM/DCM 16SOIC
NCP1606BDR2G
IC POWER FACTOR CONTROLLER 8SOIC
NCP1607BDR2G
IC PFC CONTROLLER CRM 8SOIC
NCP1611BDR2G
IC PFC CTLR HE ENHANCED 8-SOIC
NCP1651DR2G
IC PFC CONTROLLER CCM/DCM 16SOIC
NCP1654BD133R2G
IC PFC CCM 133KHZ 8-SOIC
相关代理商/技术参数
NCP1579DR2G
功能描述:电压模式 PWM 控制器 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1580DR2
功能描述:电压模式 PWM 控制器 Low Voltage RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1580DR2G
功能描述:电压模式 PWM 控制器 Low Voltage Synchronous Buck RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1581DR2G
功能描述:电压模式 PWM 控制器 SYNCHRONOUS PWM BUCK CONV RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1581SBCKRGEVB
功能描述:BOARD EVAL NCP1581 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
NCP1582ADR2G
功能描述:电压模式 PWM 控制器 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1582DR2G
功能描述:电压模式 PWM 控制器 ANA BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
NCP1582DR2GEVB
功能描述:电源管理IC开发工具 ANA SWITCH REG EVAL BOARD
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
